Operating rules of gear machine tool

Machine of bevel gear gear-shaping: Y236 (526) , Y236-3 (5A26) . 2.

Arc ages bevel gear mill ages machine: Y2250, Y2280 (528C) , 528. 3.

Gear-hobbing machine: Y31 (5A301) , YZ3120, YZ3120/11, Y3150 (Y35) , Y3150E, YM3150E, Y37 (532) , Y38 (5 д 32) , J38, Y38A, Y38-1, Y3180, Y3180E, Y3180H, J310, Y31125, Y31125, YM31125E, J315, Y320. 4.

Gear shaving machine: Y4232c (5714) , Y4232, Y4236, Y4245 (5715) , Y42125A, SYKES, ZSA550. 5.

Machine of top gem tine: Y4650. 6.

Insert tine machine: Y52 (5A12) , Y5135, Y54 (514) , J54, Y54A, Y58 (5A150) , X218, Y5150, 5M14, OH6, VR2B, OH4. 7.

Spline axis milling machine: J63K, Y631K, YB6012A, YZ6012, YB6016, 5618, 5618A, 5350, YB6012. 8.

Gear pours horny chance: YJ9332, YB9332, 9155, Y9250, Y9380, 5582. 9.

Gear examination machine: Y94 (5725M) , Y9550, Y9932. 10.

Other gear machine tool: CHZ6804, DCZ7509, QD-014. One.

Carry out seriously " metallic cutting machine tool is general operating rules " concerned regulation. 2.

Carry out machine tool of undermentioned concerned gear seriously current regulation: 1.

Graduation of the examination before the job, rolling cut is hanged annulus, want to keep the gap of clench the teeth with proper hold, tooth flank cleanness, lubricant and good, solid firm. 2.

Forbid motor-driven to be opposite knife or on knife, right knife or on knife beard hand is moved undertake. 3.

Implement the special provision of machine tool of undermentioned concerned gear seriously: (one) machine of bevel gear gear-shaping: 1.

The installation height that planing tool of pair of knife plate examination must use when planing tool holds clip and length are appropriate. Prevent photograph of brush of two planing tool to touch. 2.

Square feed tub wheel and shake when the stage, must notice to make both graticule aims "0" . 3.

Bed saddle moves every time after the position, must have originallied closely. 4.

Rolling cut exercise does not need when jack plane, should will shake the stage parks inter position (at 0 o'clock) on, secure what get off even board outfit in order to replace to spline axis to shake the stage swings commutative gear. (2) arc ages bevel gear mill ages machine: 1.

Before the job or in the job, should pay close attention shake whether stage oily window comes oily, if do not come,oily beard stops machine examination instantly. 2.

Work clamping force must accord with the regulation on machine tool sign, pressure short of sets, prohibit the work. 3.

Square feed tub wheel and shake when the stage, must notice to make both graticule aims "0" . 4.

Bed saddle moves every time after the position, must have originallied closely. (3) gear-hobbing machine: 1.

Have suitable mill and the bed that go against mill, make when going against mill, must make hydraulic pressure equalizer effective in order to reduce filar lever load. 2.

Labour oppose is smooth board (or pillar) square is mixed to need position board after move and wearing angle, must have originallied closely. 3.

Treatment is cast-iron when, forbid to use the oil that cut pass the time in a leisurely way. 4.

Often should keep clear of cut bits, prevent the accumulation that cut bits overmuch, lest bits foam be accompanying cuts disappear oil to enter workbench,guide machine, grind bad machine tool. 5.

Y320 gear-hobbing machine is searching when workpiece, workbench slewing speed is minutely must not exceed 1 to turn; Number of rolling cut tine is little at 20 tine are the following, want to reduce hob revolution, lest damage worm wheel; Should notice lathe bed lateral is lubricant seriously signal lamp, if red light is bright when, state lubricant system has trouble namely, must stop machine examination instantly. (4) machine of shave tine, top gem tine: 1.

Length of labour oppose journey, beard square arrives than be being machined the millimeter of facewidth much 5~10 of gear. When gear must compare shave helical gear, shave is choosing larger empty knife position. 2.

After with the hand knife of the as it happens that change mix ages with its the clench the teeth of base reachs its backlash, beard dot moves 2~3 Zhou Que to admit to just can make shave cut treatment normally. 3.

Mental allowance must not exceed tine base 0.

15~0.

20 millimeter. 4.

Shave is cut in the sufficient refrigeration that must hold shave tine knife. (5) the machine that insert tine: 1.

According to tine base journey of slotting tool of the most correct square, want to make sure slotting tool has capacity of sufficient light locomotive trip to forbid to touch a knife again already, when machining double couplet gear especially, should notice more. 2.

Use fast electric machinery to search when cutting tool, beard first pawl of come away feed; Benefit has fast electric machinery to search to aging when base, must take off make sb the first aim of attack to provide circumgyrate to be united in wedlock first child. CNC Milling